0 Members and 1 Guest are viewing this topic.

*

Offline Deskmate

  • *****
  • 174
  • I'm loving deskmate, yoh!
    • Giving opportunities to Zim Students
  • City: Harare
  • Current Education: Sabbatical
River Processes
« on: February 10, 2016, 03:48:13 PM »

Rivers have a lot of energy and because they have energy, they do stuff. The obvious things rivers do with their energy is flow but, besides this, they also transport load, erode load and erode the channel through which they flow.
  Erosion Erosion is the breaking down of material by an agent. In the case of a river, the agent is water. The water can erode the riverís channel and the riverís load. A riverís load is bits of eroded material, generally rocks, that the river transports until it deposits its load.
A riverís channel is eroded laterally and vertically making the channel wider and deeper. The intensity of lateral and vertical erosion is dictated by the stage in the riverís course, discussed in more detail here but essentially, in the upper stage of the riverís course (close to the source of the river) there is little horizontal erosion and lots of vertical erosion. In the middle and lower stages vertical erosion is reduced and more horizontal erosion takes place.
There are several different ways that a river erodes its bed and banks. The first is hydraulic action, where the force of the water removes rock particles from the bed and banks. This type of erosion is strongest at rapids and waterfalls where the water has a high velocity. The next type of erosion is corrasion1. This is where the riverís load acts almost like sandpaper, removing pieces of rock as the load rubs against the bed & banks. This sort of erosion is strongest when the river is transporting large chunks of rock or after heavy rainfall when the riverís flow is turbulent.
Corrosion is a special type of erosion that only affects certain types of rocks. Water, being ever so slightly acidic2, will react with certain rocks and dissolve them. Corrosion is highly effective if the rock type of the channel is chalk or limestone (anything containing calcium carbonate) otherwise, it doesnít have much of an effect.
Cavitation is an interesting method of erosion. Air bubbles trapped in the water get compressed into small spaces like cracks in the riverís banks. These bubbles eventually implode creating a small shockwave that weakens the rocks. The shockwaves are very weak but over time the rock will be weakened to the point at which it falls apart.
The final type of erosion is attrition. Attrition is a way of eroding the riverís load, not the bed and banks. Attrition is where pieces of rock in the riverís load knock together, breaking chunks of rock off of one another and gradually rounding and shrinking the load.
  Transportation When a river erodes the eroded material becomes the riverís load and the river will then transport this load through its course until it deposits the load. There are a few different ways that a river will transport load depending on how much energy the river has and how big the load is.
The largest of particles such as boulders are transported by traction. These particles are rolled along the bed of the river, eroding the bed and the particles in the process, because the river doesnít have enough energy to move these large particles in any other way.
Slightly smaller particles, such as pebbles and gravel, are transported by saltation. This is where the load bounces along the bed of the river because the river has enough energy to lift the particles off the bed but the particles are too heavy to travel by suspension.
Fine particles like clay and silt are transported in suspension, they are suspended in the water. Most of a riverís load is transported by suspension.
Solution is a special method of transportation. This is where particles are dissolved into the water so only rocks that are soluble, such as limestone or chalk, can be transported in solution.
  Capacity & Competence Rivers can only carry so much load depending on their energy. The maximum volume of load that a river can carry at a specific point in its course is called the riverís capacity. The biggest sized particle that a river could carry at a specific point is called the riverís competence.
  Deposition To transport load a river needs to have energy so when a river loses energy it is forced to deposit its load. Thereís several reasons why a river could lose energy. If the riverís discharge is reduced then the river will lose energy because it isnít flowing as quickly anymore. This could happen because of a lack of precipitation or an increase in evaporation. Increased human use (abstraction) of a river could also reduce its discharge forcing it deposit its load.
If the gradient of the riverís course flattens out, the river will deposit its load because it will be travelling a lot slower. When a river meets the sea a river will deposit its load because the gradient is generally reduced at sea level and the sea will absorb a lot of energy.
  The HjulstrŲm Curve A HjulstrŲm curve is a special type of graph that shows how a riverís velocity affects it competence and its ability to erode particles of different sizes. Thereís a lot going on on the graph but itís fairly easy to read once you get the hang of it:



Thereís two curves on the HjulstrŲm Curve, a critical erosion velocity curve and a mean settling velocity curve. The critical erosion curve shows the minimum velocity needed to transport and erode a particle. The mean settling velocity shows the minimum speed that particles of different sizes will be deposited by the river. The shaded areas between the curves show the different process that will be taking place for particles that lie in those shaded areas.
As an example, a river flowing at 10cms-1 will transport clay, silt and sand particles but will deposit gravel, pebble and boulder particles. Conversely, a river flowing at 100cms-1 will erode and transport large clay particles, silt particles, sand particles and most gravel particles. It will transport all but the largest of pebbles and will deposit boulders.
The easiest way to read the curve is to draw a horizontal line from the velocity youíre trying to read and seeing which shaded area it crosses the particle size youíre interested in in. This will tell you whether that particle is eroded, transported or deposited at that velocity.
Thereís a few interesting things to note about the HjusltrŲm Curve. The first is that clay sized particles donít appear to have a mean settling velocity. This is because these particles are so fine that a river would have to be almost perfectly stationary in order for them to fall out of solution. In addition, the small particles seem to have an erosive velocity thatís the same as the velocity for larger particles. This is because smaller particles are cohesive, they stick together, making them harder to dislodge and erode without high velocities.
We're former students so we know what we are saying.... We have a bit of teachers too.

 

River Landforms

Started by Deskmate

Replies: 0
Views: 376
Last post February 10, 2016, 03:36:21 PM
by Deskmate


Deskmate 3.0 © 2016, Deskmate by Tremmly.com